Found 6 Ways to Fix Code P1101 on Chevy Cruze

Written and Checked By:

So, your Chevy Cruze shows a P1101 Error code on the OBD II scanner tool. You can see other codes such as P1001, P1100, P1102, P1103, P1104, or P1105, which point to the same system.

What is the P1101 code?

Code P1101 Chevy Cruze

The above picture shows the P1101 code on a scanner tool and you might see different kinds of interface based on the tool used. But the point is P1101 code itself.

The P1101 code means the MAF (Mass Air Flow) sensor is out of the self-test range or has an intake airflow system performance issue. The MAF sensor calculates the amount of air entering the engine and sends that info to the Engine Control Unit (ECU).

If the signal is abnormal or missing, the Check Engine Light will come on and the P1101 code will be stored in the ECU memory.

What are the causes of the P1101 code?

We mostly know the MAF sensor is responsible for P1101. But the thing is there are some other potential causes and those are mostly overlooked.

  1. Issue with Air Filter
  2. Bad or dirty MAF sensor
  3. Dirty throttle body
  4. Bad MAP sensor
  5. Wiring issue

How to Fix P1101 Code on Chevy Cruze

You should not expect a single solution for this trouble code. There could be multiple reasons that can trigger this and we are gonna discuss them soon.

Make sure you check all the steps carefully as any of the following solutions can fix your trouble code.

Solution 1: Check the air filter

Before going into the MAF sensor you should check the air filter and see if it is somehow dirty. If it is, you need to clean it nicely. You can also replace it with a new one if the old one is too bad.

Because, a dirty or clogged air filter can limit the airflow to the engine and affect the MAF sensor reading.

Solution 2: Clean the MAF sensor

Now clean the MAF sensor with a special cleaner or a soft cloth whatever you are comfort with. Also check if the sensor connector are tight and fitted properly.

The MAF sensor is located near the air filter box and has a wire connector attached to it.

You need to disconnect the wire connector and remove the sensor from the air intake duct.

Then, you need to spray the cleaner on the sensor or wipe it gently with the cloth. Be careful not to damage the sensor or touch the wires.

After cleaning, you need to reinstall the sensor and reconnect the wire connector.

Solution 3: Check the MAP sensor

The MAP sensor is another sensor that measures the air pressure in the intake manifold. I strongly suggest check it along with the MAF sensor.

The location of this sensor is on the top of the engine and has a vacuum hose and a wire connector attached to it.

You need to check the vacuum hose and the wire connector for any loose connections or damages.

If there are any, you need to repair or replace them. You can also test the MAP sensor with a multimeter or a scan tool to see if it is working properly.

Solution 4: Clean the throttle body

After checking the MAP and MAF sensors, you need to check the throttle body.

Dirty throttle body can trigger a lot of warning lights.

Clean the throttle body with a throttle body cleaner or a soft cloth. Then remove the air intake duct and the wire connector from the throttle body and spray the cleaner on the valve and the bore.

You can also use the cloth to wipe off any dirt or carbon deposits.

Be careful not to damage the valve or the sensor. After cleaning, you need to reinstall the air intake duct and the wire connector.

Solution 5: Check the turbo cooler hoses

If your Chevy Cruze has a turbocharged engine, you must check the turbo cooler hoses for any cracks or looseness.

The turbo cooler hoses are the rubber hoses that connect the turbocharger to the intercooler and the intercooler to the throttle body.

Properly check and see if they are loose, torn, or collapsed. If they are, fix them.

Solution 6: Check the PCV valve and hose

As this one in the last of the list but this is important trust me so do not skip it.

The PCV valve and hose are important for controlling pressure in the engine and recycling gases to the intake manifold.

Find them on the valve cover with a rubber hose and wire connector attached. Here’s what you do:

  1. Check for Clogs or Leaks: Examine the PCV valve and hose for any blockages or leaks.
  2. Test the PCV Valve: Give it a simple test. Blow and suck air through it. If you can feel the air moving both ways, the valve is faulty and needs changing.
  3. Inspect the Hose: If the valve is okay, check the hose. Look for cracks or kinks. If you find any, replace it with a new one for smooth engine operation.

Clear the code

When you complete the steps above, make sure to clear the P1101 code from the ECU memory before test-driving your Chevy Cruze.

You can clear the code by using a scan tool or by disconnecting the battery for a few minutes. Then, you need to drive the car for a while and see if the code comes back on or if the symptoms persist.

If they do, you may need to check the other possible causes or take the car to a professional mechanic for further diagnosis and repair.

📟 Other potential trouble codes
|| Why P0420 Code Keeps Coming Back?

How much does it cost?

You know the cost depends on the specific cause and the parts needed. I can give you an estimation which gonna be close to the reality:

  • Air filter: Around $30
  • MAF sensor: $70
  • MAP sensor: $60
  • Throttle body: $100 – $200

The range is from $140 to $550. though the range is pretty wide so its better to get a quote from a mechanic or dealer.


Leave a Reply

Your email address will not be published. Required fields are marked *